-
Flow induced residual stress is the major reason for stress cracking and warping of plastic products, the study on which is significant to overcome the flaws of products. In this paper, the energy equation based on Extended Pom-Pom constitutive relationship is deduced. A non-isothermal viscoelastic-Newtonian two-phase fluid model for mold filling process of viscoelastic materials is set up. The conservative interface capturing technique and the flow field solving method are coupled to perform a dynamic simulation. The distribution of the frozen skin layer and the shear rates are given. The flow induced residual stress is predicted and analyzed. The numerical results show that the thickness of the frozen skin layer is dependent on the injection velocity and a higher injection velocity corresponds to a thin frozen skin layer. Near the walls of the product, the shear rate and the residual stress are almost zero. At the position of subsurface, the shear rate and the residual stress reach their largest values. At the positions far away from the walls of the product, the shear rate and the residual stress are small.
-
Keywords:
- viscoelastic /
- mold filling /
- flow induced residual stress /
- finite volume method
[1] Shen C Y 2009 Simulation of Injection Molding and Theories and Methods for Optimization of Moulds Designing (Beijing: Science Press) p1-23 (in Chinese) [申长雨 2009 注塑成型模拟及模具优化设计理论与方法(北京:科学出版社) 第1—23页]
[2] Yang B X, Ouyang J, Li X J 2012 Acta Phys. Sin. 61 044701 [杨斌鑫, 欧阳洁, 栗雪娟 2012 61 044701]
[3] Sethian J A 1999 SIAM Review 41 199
[4] Osher S, Sethian J A 1988 J. Comput. Phys. 79 12
[5] Osher S, Fedkiw R P 2001 J. Comput. Phys. 169 463
[6] Sussman M, Fatemi E, Smereka P, Osher S 1998 Computational Fluids 27 663
[7] Aboubacar M, Aguayo J P, Phillips P M, Phillips T N, Tamaddon-Jahromi H R, Snigerev B A, Webster M F 2005 Journal of Non-Newtonian Fluid Mechanics 126 207
[8] Peters G W M, Baaijens F P T 1997 Journal of Non-Newtonian Fluid Mechanics 68 205
[9] Peters G W M 1993 Thermorheological Modeling of Viscoelastic Materials (Dordrecht: Kluwer Academic Publishers) p1-200
[10] Oliveira P J, Pinho F T, Pinto G A 1998 Journal of Non-Newtonian Fluid Mechanics 79 1
[11] Yang B X, Ouyang J, Jiang T, Liu C T 2010 CMES-Computer Modeling in Engineering and Sciences 63 191
[12] Harten A, Osher S 1987 SIAM Journal Numerical Analysis 24 279
[13] Liu X D, Osher S, Chan T 1994 J. Comput. Phys. 115 217
[14] Jiang G S, Peng D P 2000 SIAM Journal on Scientific Computing 21 2126
[15] Harten A 1983 J. Comput. Phys. 49 357
[16] Beaumont J P, Nagel R, Sherman R 2002 Successful Injection Molding: Process, Design and Simulation (Cincinnati: Hanser Publisher) p1-391
-
[1] Shen C Y 2009 Simulation of Injection Molding and Theories and Methods for Optimization of Moulds Designing (Beijing: Science Press) p1-23 (in Chinese) [申长雨 2009 注塑成型模拟及模具优化设计理论与方法(北京:科学出版社) 第1—23页]
[2] Yang B X, Ouyang J, Li X J 2012 Acta Phys. Sin. 61 044701 [杨斌鑫, 欧阳洁, 栗雪娟 2012 61 044701]
[3] Sethian J A 1999 SIAM Review 41 199
[4] Osher S, Sethian J A 1988 J. Comput. Phys. 79 12
[5] Osher S, Fedkiw R P 2001 J. Comput. Phys. 169 463
[6] Sussman M, Fatemi E, Smereka P, Osher S 1998 Computational Fluids 27 663
[7] Aboubacar M, Aguayo J P, Phillips P M, Phillips T N, Tamaddon-Jahromi H R, Snigerev B A, Webster M F 2005 Journal of Non-Newtonian Fluid Mechanics 126 207
[8] Peters G W M, Baaijens F P T 1997 Journal of Non-Newtonian Fluid Mechanics 68 205
[9] Peters G W M 1993 Thermorheological Modeling of Viscoelastic Materials (Dordrecht: Kluwer Academic Publishers) p1-200
[10] Oliveira P J, Pinho F T, Pinto G A 1998 Journal of Non-Newtonian Fluid Mechanics 79 1
[11] Yang B X, Ouyang J, Jiang T, Liu C T 2010 CMES-Computer Modeling in Engineering and Sciences 63 191
[12] Harten A, Osher S 1987 SIAM Journal Numerical Analysis 24 279
[13] Liu X D, Osher S, Chan T 1994 J. Comput. Phys. 115 217
[14] Jiang G S, Peng D P 2000 SIAM Journal on Scientific Computing 21 2126
[15] Harten A 1983 J. Comput. Phys. 49 357
[16] Beaumont J P, Nagel R, Sherman R 2002 Successful Injection Molding: Process, Design and Simulation (Cincinnati: Hanser Publisher) p1-391
Catalog
Metrics
- Abstract views: 8213
- PDF Downloads: 495
- Cited By: 0
下载:
