基于电路模拟吸收体的宽带吸波型频率选择表面设计

赵宇婷; 李迎松; 杨国辉

doi:10.7498/aps.69.20200641

摘要

设计了一种加载集总电阻的单极化低频透射吸波型频率选择表面(absorptive frequency selective surface, AFSS). 该结构由二维有耗频率选择表面(FSS)阻抗屏和三维带阻FSS级联组成. 利用集总电阻加载的容性FSS和高选择性的三维宽阻带FSS实现了超宽带通响应以及低剖面、高选择性特性. 仿真结果显示设计的吸波型频率选择表面通带为1—3.5 GHz, 吸波频段为6.6—11.6 GHz, 通带与吸波频段的过渡带比为1.9. 最后制作实物进行了实验验证, 测试结果与仿真基本一致, 充分验证了设计的有效性和正确性.

关键词:

Abstract

In this paper, a single polarized absorptive frequency selective surface (AFSS) with ultra-wide transmission band and broad absorption band has been proposed numerically and experimentally. Based on the principle of circuit analog absorber (CAA), the proposed wideband AFSS is realized via replacing the ground plane with a band-stop frequency selective sturcture. The proposed AFSS is finally a hybrid structure composed of a wideband lossy frequency selective surface (FSS) in the top and a 3D band-stop frequency selective structure in the bottom. The wideband lossy FSS with thinner profile in the top is realized by utilizing a low pass capasitive elements to compensate the equivalent load inductance arising from the air space that is less than quarter wavelength installing between FSS and ground plane, and the low pass capactive lossy FSS is synthesized using “Gong”-shaped patterns with lumped resistors. Meanwhile, the unit cell of 3D frequency selective structure consists of two electrical coupling C-shaped patterns is investigated to achieve a wide stop band with high selectivity, which can be equivalent to the ground plane in the absorption band. By cascading the wideband lossy FSS and the 3D band-stop frequency selective structure, a thinner hybrid AFSS is presented with ultra-wide transmission band and broad absorption band. The results obtained from simulation shown that an absorption band with absorptivity above 90% is obtained from 6.6 to 11.6 GHz, and the 1 dB transmisson band is from 1 to 3.5 GHz with minimum insertion loss of 0.21 dB. Moreover, the performance can be guaranteed for TE-polarized oblique incidence up to 30°. Finally, a prototype is fabricated to validate its performance, the measured results shown that the 1 dB transmission band ranges from 1 to 3.5 GHz, and the absorption band is operating from 6.3 to 11 GHz at normal TE-polarized incidence. A good agreement between the experiment and simulation results is achieved, which verifies the effectiveness of the design.

Keywords:

absorptive frequency selective surface /
circuit analog absorber /
ultra-wide pass band /
split ring resonator (SRR)

作者及机构信息

1.
哈尔滨工程大学信息与通信工程学院, 哈尔滨　150001

2.
哈尔滨工业大学电子与信息工程学院, 哈尔滨　150001

通信作者: 李迎松, liyingsong@ieee.org

基金项目: 国家重点研发计划(批准号: 2016YFE0111100)、黑龙江重点研发计划(批准号: GX17A016)和中国博士后基金(批准号: 201M620918, 2019T120134)资助的课题

Authors and contacts

1.
College of Information and Communication Engineering, Harbin Engineering University, Harbin 150001, China

2.
School of Electronic and Information Engineering, Harbin Institute of Technology, Harbin 150001, China

Corresponding author: Li Ying-Song, liyingsong@ieee.org

Funds: Project supported by the National Key Research and Development Program of China (Grant No. 2016YFE0111100), the Key Research and Development Program of Heilongjiang Province, China (Grant No. GX17A016), and the China Postdoctoral Science Foundation (Grant Nos. 2017M620918, 2019T120134)

文章全文 : translate this paragraph

参考文献

[1]	Munk B A 2000 Frequency Selective Surfaces: Theory and Design (NewYork: Wiley) pp12–20.
[2]	Munk B A 2009 Metamaterials: Critique and Alternatives (Hoboken: Wiley) pp50–56.
[3]	Costa F, Monorchio A 2012 IEEE Trans. Antennas Propag. 60 2740 Google Scholar
[4]	周航, 屈绍波, 彭卫东, 王甲富, 马华, 张东伟, 张介秋, 柏鹏, 徐卓 2012 61 104201 Google Scholar Zhou H, Qu S B, Peng W D, Wang J F, Ma H, Zhang D W, Zhang J Q, Bai P, Xu Z 2012 Acta Phys. Sin. 61 104201 Google Scholar
[5]	Zhong S, Wu L, Liu T, Huang J, Jiang W, Ma Y 2018 Opt. Express. 26 16466 Google Scholar
[6]	Chen Q, Sang D, Guo M, Fu Y Q 2019 IEEE Trans. Antennas Propag. 67 1045 Google Scholar
[7]	Wang Z F, Fu J H, Zeng Q S, Song M X, Denidni T A 2019 IEEE Trans. Antennas Propag. 18 1443 Google Scholar
[8]	Guo Q X, Li Z R, Su J X, Yang L Y, Song J M 2019 IEEE Trans. Antennas Propag. 18 961 Google Scholar
[9]	Chen Q, Liu L G, Chen L, Bai J J, Fu Y Q 2016 Electron. Lett. 52 418 Google Scholar
[10]	Zhang Y X, Li B, Zhu L, Tang Y M, Chang Y M, Bo Y M 2018 IEEE Antennas Wirel. Propag. Lett. 17 633 Google Scholar
[11]	Shen Z X, Wang J, Li B 2016 IEEE Trans. Antennas Propag. 64 3087 Google Scholar
[12]	Luo G Q, Hong W, Tang H J, Chen J X, Wu K 2006 IEEE Microw. Wirel. Compon. Lett. 16 648 Google Scholar
[13]	Rashid A K, Shen Z X 2010 IEEE Antennas and Propagation Society International Symposium Toronto, Canada, July 11–17, 2010 p978
[14]	Yu W L, Luo G Q, Yu Y F, Liao Z, Jin H Y, Shen Z X 2019 IEEE Antennas Wirel. Propag. Lett. 18 1701 Google Scholar
[15]	Yu W L, Luo G Q, Yu Y F, Cao W H, Pan Y J, Shen Z X 2019 IEEE Trans. Antennas Propag. 67 1318 Google Scholar
[16]	Yu Y F, Luo G Q, Liu Q, Yu W L, Jin H Y, Liao Z, Shen Z X 2019 IEEE Access. 7 2520 Google Scholar
[17]	波扎著 (张肇仪译) 2010 微波工程 (北京: 电子工业出版社) 第157—160页 Pozer D M (translated by Zhang Z Y) 2010 Microwave Engineering (Beijing: Electronic Industry Press) pp157–160 (in Chinese)
[18]	Costa F, Monorchio A, Manara G 2016 IEEE Electromagnetic Compatibility Magazine. 5 67 Google Scholar
[19]	周良 2011 博士学位论文 (南京: 南京航空航天大学) Zhou L 2011 Ph. D. Dissertation (Nanjing: Nanjing University of Aeronautics and Astronautics) (in Chinese)
[20]	Ghodgaonkar D K, Varadan V V, Varadan V K IEEE 1989 Trans. Instrum. Meas. 38 789 Google Scholar

施引文献

图 1 电路示意图　(a) 吸波体; (b) AFSS

Fig. 1. Circuit Model: (a) Absorber; (b) AFSS.

下载: 全尺寸图片幻灯片

图 2 吸波体结构设计　(a) 三维视图; (b) 正视图

Fig. 2. Design of the absorber: (a) 3-D view; (b) front view.

下载: 全尺寸图片幻灯片

图 3 吸波体特性　(a) S₁₁与吸收率; (b) 阻抗特性

Fig. 3. Characteristic of the absorber: (a) S₁₁ and absorptivity; (b) impedance characteristic.

下载: 全尺寸图片幻灯片

图 4 带阻FSS　(a)单元设计; (b)等效电路

Fig. 4. Band-stop FSS: (a) The design of unit cell; (b) equivalent circuit.

下载: 全尺寸图片幻灯片

图 5 带阻FSS的等效电路仿真与全波仿真结果对比

Fig. 5. Comparison between simulation results and full wave simulation.

下载: 全尺寸图片幻灯片

图 6 (a) AFSS的3 × 1周期结构示意图; (b)TE极化波入射下的S参数与吸收率; (c) TE极化波斜入射时的反射系数与传输系数

Fig. 6. (a) Geometry of the proposed AFSS (3 × 1 periodic structure); (b) S parameters and absorptivity at TE-polarized incidence; (c) reflection/transmission coefficients at TE-polarized oblique incidences.

下载: 全尺寸图片幻灯片

图 7 AFSS样品　(a)有耗FSS; (b)带阻FSS

Fig. 7. Fabricated AFSS: (a) Lossy FSS; (b) bandstop FSS.

下载: 全尺寸图片幻灯片

图 8 (a)实验装置(b) S参数的仿真结果与测量结果的对比

Fig. 8. (a) Experimental setup; (b) comparison between simulated and measured S parameters.

下载: 全尺寸图片幻灯片

表 1 所设计AFSS与前人所设计的AFSS比较

Table 1. Comparisons between the proposed AFSS and the previous AFSSs.

参考文献	通带频段/GHz	吸波段分数带宽/%	${\rm{F}}{{\rm{R}}_{{\rm{ap}}}}$	${f_{\rm{a}}}$/ GHz	尺寸(@${f_a}$)	极化	结构
[14]	2—2.82	39.8	2.1	7.9	0.24 × 0.24 × 0.36	单极化	混合
[15]	≤ 1.54	34.6	3.1	4.8	0.14 × 0.14 × 0.13	单极化	三维
[16]	≤ 1.28	43	3.3	4.2	0.21 × 0.17 × 0.17	双极化	二维
本文	1—3.5	54	1.8	6.3	0.1 × 0.17 × 0.3	单极化	混合

下载: 导出CSV

map

[1]	Munk B A 2000 Frequency Selective Surfaces: Theory and Design (NewYork: Wiley) pp12–20.
[2]	Munk B A 2009 Metamaterials: Critique and Alternatives (Hoboken: Wiley) pp50–56.
[3]	Costa F, Monorchio A 2012 IEEE Trans. Antennas Propag. 60 2740 Google Scholar
[4]	周航, 屈绍波, 彭卫东, 王甲富, 马华, 张东伟, 张介秋, 柏鹏, 徐卓 2012 61 104201 Google Scholar Zhou H, Qu S B, Peng W D, Wang J F, Ma H, Zhang D W, Zhang J Q, Bai P, Xu Z 2012 Acta Phys. Sin. 61 104201 Google Scholar
[5]	Zhong S, Wu L, Liu T, Huang J, Jiang W, Ma Y 2018 Opt. Express. 26 16466 Google Scholar
[6]	Chen Q, Sang D, Guo M, Fu Y Q 2019 IEEE Trans. Antennas Propag. 67 1045 Google Scholar
[7]	Wang Z F, Fu J H, Zeng Q S, Song M X, Denidni T A 2019 IEEE Trans. Antennas Propag. 18 1443 Google Scholar
[8]	Guo Q X, Li Z R, Su J X, Yang L Y, Song J M 2019 IEEE Trans. Antennas Propag. 18 961 Google Scholar
[9]	Chen Q, Liu L G, Chen L, Bai J J, Fu Y Q 2016 Electron. Lett. 52 418 Google Scholar
[10]	Zhang Y X, Li B, Zhu L, Tang Y M, Chang Y M, Bo Y M 2018 IEEE Antennas Wirel. Propag. Lett. 17 633 Google Scholar
[11]	Shen Z X, Wang J, Li B 2016 IEEE Trans. Antennas Propag. 64 3087 Google Scholar
[12]	Luo G Q, Hong W, Tang H J, Chen J X, Wu K 2006 IEEE Microw. Wirel. Compon. Lett. 16 648 Google Scholar
[13]	Rashid A K, Shen Z X 2010 IEEE Antennas and Propagation Society International Symposium Toronto, Canada, July 11–17, 2010 p978
[14]	Yu W L, Luo G Q, Yu Y F, Liao Z, Jin H Y, Shen Z X 2019 IEEE Antennas Wirel. Propag. Lett. 18 1701 Google Scholar
[15]	Yu W L, Luo G Q, Yu Y F, Cao W H, Pan Y J, Shen Z X 2019 IEEE Trans. Antennas Propag. 67 1318 Google Scholar
[16]	Yu Y F, Luo G Q, Liu Q, Yu W L, Jin H Y, Liao Z, Shen Z X 2019 IEEE Access. 7 2520 Google Scholar
[17]	波扎著 (张肇仪译) 2010 微波工程 (北京: 电子工业出版社) 第157—160页 Pozer D M (translated by Zhang Z Y) 2010 Microwave Engineering (Beijing: Electronic Industry Press) pp157–160 (in Chinese)
[18]	Costa F, Monorchio A, Manara G 2016 IEEE Electromagnetic Compatibility Magazine. 5 67 Google Scholar
[19]	周良 2011 博士学位论文 (南京: 南京航空航天大学) Zhou L 2011 Ph. D. Dissertation (Nanjing: Nanjing University of Aeronautics and Astronautics) (in Chinese)
[20]	Ghodgaonkar D K, Varadan V V, Varadan V K IEEE 1989 Trans. Instrum. Meas. 38 789 Google Scholar

[1]	王东俊, 孙子涵, 张袁, 唐莉, 闫丽萍. 抗方阻波动的超宽带轻薄频率选择表面吸波体. , 2024, 73(2): 024201. doi: 10.7498/aps.73.20231365
[2]	葛宏义, 李丽, 蒋玉英, 李广明, 王飞, 吕明, 张元, 李智. 基于双开口金属环的太赫兹超材料吸波体传感器. , 2022, 71(10): 108701. doi: 10.7498/aps.71.20212303
[3]	惠忆聪, 王春齐, 黄小忠. 基于电阻型频率选择表面的宽带雷达超材料吸波体设计. , 2015, 64(21): 218102. doi: 10.7498/aps.64.218102
[4]	刘红喜, 高军, 曹祥玉, 刘艳芳, 张迪, 李思佳. 一种基于开口谐振环的高增益端射天线设计. , 2015, 64(23): 234101. doi: 10.7498/aps.64.234101
[5]	刘海文, 占昕, 任宝平. 射电天文用太赫兹三通带频率选择表面设计. , 2015, 64(17): 174103. doi: 10.7498/aps.64.174103
[6]	徐永顺, 别少伟, 江建军, 徐海兵, 万东, 周杰. 含螺旋单元频率选择表面的宽频带强吸收复合吸波体. , 2014, 63(20): 205202. doi: 10.7498/aps.63.205202
[7]	戴雨涵, 陈小浪, 赵强, 张继华, 陈宏伟, 杨传仁. 太赫兹波段谐振频率可调的开口谐振环结构. , 2013, 62(6): 064101. doi: 10.7498/aps.62.064101
[8]	程用志, 聂彦, 龚荣洲, 郑栋浩, 范跃农, 熊炫, 王鲜. 基于超材料与电阻型频率选择表面的薄型宽频带吸波体的设计. , 2012, 61(13): 134101. doi: 10.7498/aps.61.134101
[9]	程用志, 王莹, 聂彦, 郑栋浩, 龚荣洲, 熊炫, 王鲜. 基于电阻型频率选择表面的低频宽带超材料吸波体的设计. , 2012, 61(13): 134102. doi: 10.7498/aps.61.134102
[10]	李芸, 孙华. 开口共振环型球状变形器的设计与模拟. , 2011, 60(9): 094103. doi: 10.7498/aps.60.094103
[11]	陈谦, 江建军, 别少伟, 王鹏, 刘鹏, 徐欣欣. 含有源频率选择表面可调复合吸波体. , 2011, 60(7): 074202. doi: 10.7498/aps.60.074202
[12]	樊京, 蔡广宇. 一种基于旋转调谐的超材料. , 2010, 59(12): 8574-8578. doi: 10.7498/aps.59.8574
[13]	樊京, 蔡广宇. 一种基于金属开口谐振环和杆阵列的左手材料宽带吸收器. , 2010, 59(9): 6084-6088. doi: 10.7498/aps.59.6084
[14]	杨锐, 谢拥军, 李晓峰, 蒋俊, 王元源, 王瑞. 异向介质谐振响应的Floquet模分析. , 2009, 58(2): 901-907. doi: 10.7498/aps.58.901
[15]	杨锐, 谢拥军, 王元源, 傅焕展. 加载异向介质非辐射介质波导中的慢波传输及应用. , 2008, 57(9): 5513-5518. doi: 10.7498/aps.57.5513
[16]	艾芬, 白洋, 徐芳, 乔利杰, 周济. 基于铁氧体基板的开口谐振环的可调微波左手特性研究. , 2008, 57(7): 4189-4194. doi: 10.7498/aps.57.4189
[17]	张富利, 赵晓鹏. 谐振频率可调的环状开口谐振器结构及其效应. , 2007, 56(8): 4661-4667. doi: 10.7498/aps.56.4661
[18]	姚远, 赵晓鹏, 赵晶, 周欣. 非对称开口六边形谐振单环的微波透射特性. , 2006, 55(12): 6435-6440. doi: 10.7498/aps.55.6435
[19]	康　雷, 赵　乾, 赵晓鹏. 二维负磁导率材料中的缺陷效应. , 2004, 53(10): 3379-3383. doi: 10.7498/aps.53.3379
[20]	赵乾, 赵晓鹏, 康雷, 张富利, 刘亚红, 罗春荣. 一维负磁导率材料中的缺陷效应. , 2004, 53(7): 2206-2211. doi: 10.7498/aps.53.2206

计量

文章访问数: 9931
PDF下载量: 396
被引次数: 0

姓名
邮箱
手机号码
标题
留言内容
验证码

搜索

留言板