表面粗糙度对固体内部超声背散射的影响

宋永锋; 李雄兵; 史亦韦; 倪培君

doi:10.7498/aps.65.214301

摘要

超声背散射法可通过多晶体金属内部的空间方差信号，实现微观结构参数的无损评价，但表面粗糙度对评价模型的精度及实用性存在显著影响.基于高斯声束理论推导垂直入射粗糙界面的纵波声场，以此研究声能的Wigner分布规律；在超声的波长远大于粗糙度的前提下，构造表面粗糙度修正系数，并建立粗糙界面的单次散射响应模型，揭示粗糙度对超声波背向散射的影响规律.用304不锈钢制备轮廓均方根值为0.159 m的光滑试块和25.722 m的粗糙试块开展超声背散射实验，结果表明模型在粗糙度修正前后均可实现光滑试块的晶粒尺寸有效评价，但未经修正的传统模型对粗糙试块的晶粒尺寸评价结果与金相法结果的相对误差高达-21.35%，而本模型的评价结果与金相法结果符合得很好，相对误差仅为1.35%.可见，本模型能有效补偿粗糙度引起的超声背散射信号衰减，从而提高晶粒尺寸无损评价的精度.

关键词:

Abstract

In the diffuse ultrasonic backscatter describing the scattering of elastic waves from polycrystalline metal material, the spatial variance of the signal is used as a primary measure of microstructure.Previously,theoretical singly-scattered response models have been developed for the diffuse backscatters of elastic waves within polycrystalline materials,which take into consideration both transducer beams and microstructural scattering information.However,the surface roughness of the liquid-solid interface induces a noticeable change of spatial variance amplitude,and its effect on the diffuse ultrasonic backscatter that can severely degrade the accuracy and practicability of the microstructure parameter evaluation was neglected in previous models.Therefore,a new singly-scattered response model for the rough surface polycrystalline samples is developed by following the forms similar to previous models for longitudinal-to-longitudinal scattering at normal incidence.In particular, we assume that the surface is slightly rough,specifically,the surface roughness value should not be larger than the magnitude of the wavelength.Hence,the modified expressions of ultrasonic reflection and transmission coefficients for the randomly rough interface can be applied to the singly-scattered response model.Then,with the modified transmission coefficient,a Gaussian beam is adopted to model the transducer beam pattern at normal incidence for longitudinal wave propagation through a rough liquid-solid interface to the polycrystal.Next,the Wigner transform of the displacement field is derived with a parameter of the surface roughness root mean square value.After that,a new expression of the calibration parameter including the modified reflection coefficient is given to provide a conversion between the displacement field and the experimental transducer voltage.Finally,the rough surface singly-scattered response model is built and the surface roughness correction coefficient is presented here to quantify the effect of the surface roughness on diffuse ultrasonic backscatter.The numerical results show that the Wigner distribution amplitude decreases and the acoustic energy coverage shrinks with the increase of the surface roughness.The theoretical spatial variance amplitude decreases by about 79.2% when the root mean square roughness value is set to be 40 m.The surface roughness correction coefficient is usually smaller than 1 when the reference calibration sample is smooth,but it can be bigger than 1 when the reference sample is rough.The results from the developed theory are then compared with the experimental measurements associated with a pulse echo transducer configuration for 304 stainless steel by using the smooth and rough surface samples.From these measurements,the mean grain size of the stainless steel can be determined.The experimental results show that although the corrected and uncorrected models both fit the experimental spatial variance curve from the smooth surface sample well,the uncorrected model fails to extract the grain size of the rough surface sample.The relative error of the grain size between optical microscopy and the uncorrected model can reach -21.35%.In contrast,good agreement with optical microscopy is observed by using the surface roughness corrected model,and the relative error is only 1.35%.In conclusion,the ultrasonic waves transmit though the rough interface twice,and the diffuse scattering which happens in these processes reduces the number of backscatter waves that can return to the transducer,so the spatial variance amplitudes drop dramatically.The correction coefficient presented here can describe the effect of surface roughness on diffuse ultrasonic backscatter.Moreover,it can improve the accuracy of grain size evaluation effectively.Thus,the surface roughness corrected ultrasonic backscatter model may be applicable for quality control of roughwrought castings or forgings during the manufacturing.

Keywords:

作者及机构信息

1.
中南大学交通运输工程学院, 长沙 410075;

2.
北京航空材料研究院, 北京 100095;

3.
中国兵器科学研究院宁波分院, 宁波 315103

通信作者: 李雄兵, lixb213@mail.csu.edu.cn

基金项目: 国家自然科学基金（批准号：61271356，51575541）资助的课题.

Authors and contacts

1.
School of Traffic and Transportation Engineering, Central South University, Changsha 410075, China;

2.
Beijing Institute of Aeronautical Materials, Beijing 100095, China;

3.
Ningbo Branch of Ordnance Science Institute of China, Ningbo 315103, China

Corresponding author: Li Xiong-Bing, lixb213@mail.csu.edu.cn

Funds: Project supported by the National Natural Science Foundation of China(Grant Nos. 61271356, 51575541).

参考文献

[1]	Bouda A B, Lebaili S, Benchaala A 2003 NDT&E Int. 36 1
[2]	Liu Y G, Zhang S B, Han Z H, Zhao Y J 2016 Acta Phys. Sin. 65 104401(in Chinese)[刘英光, 张士兵, 韩中合, 赵豫晋2016 65 104401]
[3]	Panetta P D, Bland L G, Tracy M, Hassan W 2015 TMS 2014 Supplemental Proceedings San Diego, USA, February 16-20, 2014 p721
[4]	Gayda J, Gabb T P, Kantzos P T 2004 Superalloys Champion, USA, September 19-23, 2004 p323
[5]	Wang X H, Xiang J J, Hu H W, Xie W, Li X B 2015 Ultrasonics 60 27
[6]	Li X B, Song Y F, Ni P J, Wang Z, Liu F, Du H L 2015 Nucl. Instrum. Meth. B 351 16
[7]	nal R, Sarpn I H, Yalim H A, Erol A,Özdemir T, Tuncel S 2006 Mater. Charact. 56 241
[8]	Laux D, Cros B, Despaux G, Baron D 2002 J. Nucl. Mater. 300 192
[9]	Du H L, Turner J A 2014 Ultrasonics 54 882
[10]	Li X B, Song Y F, Liu F, Hu H W, Ni P J 2015 NDT&E Int. 72 25
[11]	Kersemans M, van Paepegem W, Lemmens B, van Den Abeele K, Pyl L, Zastavnik F, Sol H, Degrieck J 2014 Exp. Mech. 54 1059
[12]	Margetan F J, Gray T A, Thompson R B 1991 Review of Progress in Quantitative Nondestructive Evaluation La Jolla, USA, July 15-20, 1990 p1721
[13]	Rose J H 1992 Review of Progress in Quantitative Nondestructive Evaluation Brunswick, Maine, July 28-August 2, 1991 p1677
[14]	Han Y K, Thompson R B 1997 Metall. Mater. Trans. A. 28 91
[15]	Ghoshal G, Turner J A 2010 J. Acoust. Soc. Am. 128 3449
[16]	Song Y F, Li X B, Wu H P, Si J Y, Han X Q 2016 Acta Metall. Sin. 52 378(in Chinese)[宋永锋, 李雄兵, 吴海平, 司家勇, 韩晓芹2016金属学报52 378]
[17]	Margetan F J 2012 Review of Progress in Quantitative Nondestructive Evaluation Burlington, USA, July 17-22, 2011 p54
[18]	Ghoshal G, Turner J A, Weaver R L 2007 J. Acoust. Soc. Am. 122 2009
[19]	Kube C M, Du H L, Ghoshal G, Turner J A 2012 J. Acoust. Soc. Am. 132 EL43
[20]	Du H L, Lonsdale C, Oliver J, Wilson B M, Turner J A 2013 J. Nondestruct. Eval. 32 331
[21]	Hu P, Kube C M, Koester L W, Turner J A 2013 J. Acoust. Soc. Am. 134 982
[22]	Xiao Q, Wang J, Guo X S, Zhang D 2013 Acta Phys. Sin. 62 094301(in Chinese)[肖齐, 王珺, 郭霞生, 章东2013 62 094301]
[23]	Shi F, Lowe M J S, Xi X, Craster R V 2016 J. Mech. Phys. Solids 92 260
[24]	Guo Y 2003 Ph. D. Dissertation (Iowa:Iowa State University)
[25]	Margetan F J, Haldipur P, Yu L, Thompson R B 2005 Review of Progress in Quantitative Nondestructive Evaluation Golden, USA, July 25-30, 2004 p75
[26]	Cohen L 1995 Time-Frequency Analysis (Englewood Cliffs:Prentice-Hall) pp113-135
[27]	Boashash B 1988 IEEE Trans. Acoust. Speech. Signal. Process. 36 1518
[28]	Weaver R L 1990 J. Mech. Phys. Solids. 38 55
[29]	Schmerr L W, Song S J 2007 Ultrasonic Nondestructive Evaluation System (New York:Springer) pp179-234
[30]	Thompson R B, Lopes E F 1984 J. Nondestruct. Eval. 4 107
[31]	Reed F A, Batzinger T J, Reed R W, Jönsson S 1993 Review of Progress in Quantitative Nondestructive Evaluation La Jolla, USA, July 19-24, 1992 p1265
[32]	Nagy P B, Adler L 1987 J. Acoust. Soc. Am. 82 193
[33]	Schmerr L W 2000 Mater. Eval. 58 882
[34]	Kim A D, Ishimaru A 2000 BiOS 2000 The International Symposium on Biomedical Optics San Jose, USA, January 22-27, 2000 p423
[35]	Ryzhik L, Papanicolaou G, Keller J B 1996 Wave Motion 24 327
[36]	Carrier G F, Krook M, Pearson C E 1966 Functions of a Complex Variable:Theory and technique (New York:McGraw-Hill Inc.) pp301-375
[37]	Rogers P H, van Buren A L 1974 J. Acoust. Soc. Am. 55 724
[38]	Vitos L, Korzhavyi P A, Johansson B 2003 Nat. Mater. 2 25
[39]	Lerch T P, Schmerr L W, Sedov A 1996 Res. Nondestruct. Eval. 8 1
[40]	Duan X M, Zhao X Y, Sun H F 2014 Acta Phys. Sin. 63 014301(in Chinese)[段晓敏, 赵新玉, 孙华飞2014 63 014301]
[41]	Hu P, Turner J A 2015 J. Acoust. Soc. Am. 137 321

施引文献

[1]	Bouda A B, Lebaili S, Benchaala A 2003 NDT&E Int. 36 1
[2]	Liu Y G, Zhang S B, Han Z H, Zhao Y J 2016 Acta Phys. Sin. 65 104401(in Chinese)[刘英光, 张士兵, 韩中合, 赵豫晋2016 65 104401]
[3]	Panetta P D, Bland L G, Tracy M, Hassan W 2015 TMS 2014 Supplemental Proceedings San Diego, USA, February 16-20, 2014 p721
[4]	Gayda J, Gabb T P, Kantzos P T 2004 Superalloys Champion, USA, September 19-23, 2004 p323
[5]	Wang X H, Xiang J J, Hu H W, Xie W, Li X B 2015 Ultrasonics 60 27
[6]	Li X B, Song Y F, Ni P J, Wang Z, Liu F, Du H L 2015 Nucl. Instrum. Meth. B 351 16
[7]	nal R, Sarpn I H, Yalim H A, Erol A,Özdemir T, Tuncel S 2006 Mater. Charact. 56 241
[8]	Laux D, Cros B, Despaux G, Baron D 2002 J. Nucl. Mater. 300 192
[9]	Du H L, Turner J A 2014 Ultrasonics 54 882
[10]	Li X B, Song Y F, Liu F, Hu H W, Ni P J 2015 NDT&E Int. 72 25
[11]	Kersemans M, van Paepegem W, Lemmens B, van Den Abeele K, Pyl L, Zastavnik F, Sol H, Degrieck J 2014 Exp. Mech. 54 1059
[12]	Margetan F J, Gray T A, Thompson R B 1991 Review of Progress in Quantitative Nondestructive Evaluation La Jolla, USA, July 15-20, 1990 p1721
[13]	Rose J H 1992 Review of Progress in Quantitative Nondestructive Evaluation Brunswick, Maine, July 28-August 2, 1991 p1677
[14]	Han Y K, Thompson R B 1997 Metall. Mater. Trans. A. 28 91
[15]	Ghoshal G, Turner J A 2010 J. Acoust. Soc. Am. 128 3449
[16]	Song Y F, Li X B, Wu H P, Si J Y, Han X Q 2016 Acta Metall. Sin. 52 378(in Chinese)[宋永锋, 李雄兵, 吴海平, 司家勇, 韩晓芹2016金属学报52 378]
[17]	Margetan F J 2012 Review of Progress in Quantitative Nondestructive Evaluation Burlington, USA, July 17-22, 2011 p54
[18]	Ghoshal G, Turner J A, Weaver R L 2007 J. Acoust. Soc. Am. 122 2009
[19]	Kube C M, Du H L, Ghoshal G, Turner J A 2012 J. Acoust. Soc. Am. 132 EL43
[20]	Du H L, Lonsdale C, Oliver J, Wilson B M, Turner J A 2013 J. Nondestruct. Eval. 32 331
[21]	Hu P, Kube C M, Koester L W, Turner J A 2013 J. Acoust. Soc. Am. 134 982
[22]	Xiao Q, Wang J, Guo X S, Zhang D 2013 Acta Phys. Sin. 62 094301(in Chinese)[肖齐, 王珺, 郭霞生, 章东2013 62 094301]
[23]	Shi F, Lowe M J S, Xi X, Craster R V 2016 J. Mech. Phys. Solids 92 260
[24]	Guo Y 2003 Ph. D. Dissertation (Iowa:Iowa State University)
[25]	Margetan F J, Haldipur P, Yu L, Thompson R B 2005 Review of Progress in Quantitative Nondestructive Evaluation Golden, USA, July 25-30, 2004 p75
[26]	Cohen L 1995 Time-Frequency Analysis (Englewood Cliffs:Prentice-Hall) pp113-135
[27]	Boashash B 1988 IEEE Trans. Acoust. Speech. Signal. Process. 36 1518
[28]	Weaver R L 1990 J. Mech. Phys. Solids. 38 55
[29]	Schmerr L W, Song S J 2007 Ultrasonic Nondestructive Evaluation System (New York:Springer) pp179-234
[30]	Thompson R B, Lopes E F 1984 J. Nondestruct. Eval. 4 107
[31]	Reed F A, Batzinger T J, Reed R W, Jönsson S 1993 Review of Progress in Quantitative Nondestructive Evaluation La Jolla, USA, July 19-24, 1992 p1265
[32]	Nagy P B, Adler L 1987 J. Acoust. Soc. Am. 82 193
[33]	Schmerr L W 2000 Mater. Eval. 58 882
[34]	Kim A D, Ishimaru A 2000 BiOS 2000 The International Symposium on Biomedical Optics San Jose, USA, January 22-27, 2000 p423
[35]	Ryzhik L, Papanicolaou G, Keller J B 1996 Wave Motion 24 327
[36]	Carrier G F, Krook M, Pearson C E 1966 Functions of a Complex Variable:Theory and technique (New York:McGraw-Hill Inc.) pp301-375
[37]	Rogers P H, van Buren A L 1974 J. Acoust. Soc. Am. 55 724
[38]	Vitos L, Korzhavyi P A, Johansson B 2003 Nat. Mater. 2 25
[39]	Lerch T P, Schmerr L W, Sedov A 1996 Res. Nondestruct. Eval. 8 1
[40]	Duan X M, Zhao X Y, Sun H F 2014 Acta Phys. Sin. 63 014301(in Chinese)[段晓敏, 赵新玉, 孙华飞2014 63 014301]
[41]	Hu P, Turner J A 2015 J. Acoust. Soc. Am. 137 321

[1]	刘雨, 田强, 王新艳, 关雪飞. 基于单向测量超声背散射系数的晶粒尺寸评价高效方法. , 2024, 73(7): 074301. doi: 10.7498/aps.73.20231959
[2]	张凤国, 赵福祺, 刘军, 何安民, 王裴. 延性金属层裂强度对温度、晶粒尺寸和加载应变率的依赖特性及其物理建模. , 2022, 71(3): 034601. doi: 10.7498/aps.71.20210702
[3]	朱琦, 许多, 张元军, 李玉娟, 王文, 张海燕. 基于卷积神经网络的白蚀缺陷超声探测. , 2022, 71(24): 244301. doi: 10.7498/aps.71.20221504
[4]	张凤国. 延性金属层裂强度对温度、晶粒尺寸和加载应变率的依赖特性及其物理建模. , 2021, (): . doi: 10.7498/aps.70.20210702
[5]	东蕊, 刘成成, 蔡勋兵, 邵留磊, 李博艺, 他得安. 超声背散射骨质评价中的频散衰减测量与补偿. , 2019, 68(18): 184301. doi: 10.7498/aps.68.20190599
[6]	王建国, 杨松林, 叶永红. 样品表面银膜的粗糙度对钛酸钡微球成像性能的影响. , 2018, 67(21): 214209. doi: 10.7498/aps.67.20180823
[7]	李珊, 李雄兵, 宋永锋, 陈超. 考虑晶粒分布的多晶体材料超声散射统一理论. , 2018, 67(23): 234301. doi: 10.7498/aps.67.20181751
[8]	宋延松, 杨建峰, 李福, 马小龙, 王红. 基于杂散光抑制要求的光学表面粗糙度控制方法研究. , 2017, 66(19): 194201. doi: 10.7498/aps.66.194201
[9]	王鹏, 徐建刚, 张云光, 宋海洋. 晶粒尺寸对纳米多晶铁变形机制影响的模拟研究. , 2016, 65(23): 236201. doi: 10.7498/aps.65.236201
[10]	刘英光, 张士兵, 韩中合, 赵豫晋. 纳晶铜晶粒尺寸对热导率的影响. , 2016, 65(10): 104401. doi: 10.7498/aps.65.104401
[11]	陈苏婷, 胡海锋, 张闯. 基于激光散斑成像的零件表面粗糙度建模. , 2015, 64(23): 234203. doi: 10.7498/aps.64.234203
[12]	李资政, 杨海贵, 王笑夷, 高劲松. 具有大面积均匀性、高质量的大尺寸中阶梯光栅铝膜的研究. , 2014, 63(15): 157801. doi: 10.7498/aps.63.157801
[13]	曹洪, 黄勇, 陈素芬, 张占文, 韦建军. 脉冲敲击技术对PI微球表面粗糙度的影响. , 2013, 62(19): 196801. doi: 10.7498/aps.62.196801
[14]	王英龙, 张鹏程, 刘虹让, 刘保亭, 傅广生. 晶粒尺寸及衬底应力对铁电薄膜特性的影响. , 2011, 60(7): 077702. doi: 10.7498/aps.60.077702
[15]	毛朝梁, 董显林, 王根水, 姚春华, 曹菲, 曹盛, 杨丽慧, 王永令. 晶粒尺寸对Ba0.70Sr0.30TiO3陶瓷介电性能的影响规律及机理研究. , 2009, 58(8): 5784-5789. doi: 10.7498/aps.58.5784
[16]	王浩, 刘国权, 栾军华, 岳景朝, 秦湘阁. 晶粒棱长、尺寸与拓扑学特征之间关系的Monte Carlo仿真研究. , 2009, 58(13): 132-S136. doi: 10.7498/aps.58.132
[17]	周炳卿, 刘丰珍, 朱美芳, 周玉琴, 吴忠华, 陈兴. 微晶硅薄膜的表面粗糙度及其生长机制的X射线掠角反射研究. , 2007, 56(4): 2422-2427. doi: 10.7498/aps.56.2422
[18]	侯海虹, 孙喜莲, 申雁鸣, 邵建达, 范正修, 易葵. 电子束蒸发氧化锆薄膜的粗糙度和光散射特性. , 2006, 55(6): 3124-3127. doi: 10.7498/aps.55.3124
[19]	余柏林, 祁琼, 唐新峰, 张清杰. 晶粒尺寸对CoSb3化合物热电性能的影响. , 2005, 54(12): 5763-5768. doi: 10.7498/aps.54.5763
[20]	李眉娟, 胡海云, 邢修三. 多晶体金属疲劳寿命随晶粒尺寸变化的理论研究. , 2003, 52(8): 2092-2095. doi: 10.7498/aps.52.2092

计量

文章访问数: 6580
PDF下载量: 231
被引次数: 0

姓名
邮箱
手机号码
标题
留言内容
验证码

搜索

留言板