时效时间对FeNiAlTa形状记忆合金组织结构和性能的影响

杨能武; 彭文屹; 严明明; 王维维; 石海平

doi:10.7498/aps.62.158106

摘要

本文以 Fe59.5Ni28Al11.5Ta1 形状记忆合金为研究对象, 采用金相显微镜、X 射线衍射仪、扫描电镜、能谱仪和压力试验机等研究了轧制后不同时效时间处理对该合金组织结构和性能的影响. 结果表明, 随着时效的进行, γ’ 相和 β’ 相的相继析出, 强化了奥氏体基体. 综合伪弹性曲线看出, 随着时效时间的增加, 600 ℃时效态合金的应力诱发马氏体临界应力先减小后增大, 合金的抗压强度、可恢复的应变和硬度都先增大后减小, 合金的残余应变则先减小后增大, 时效时间为 60 h 时, 合金的抗压强度最大, 到达1306 MPa, 此时合金的可恢复形变最大, 达到14.9%, 合金的硬度也最大, 合金的残余应变相对最小. 但随着时效时间的延长, 合金的最大应变逐渐减小, 合金塑性逐渐减小. Fe59.5Ni28Al11.5Ta1 形状记忆合金的性能与沉淀相的颗粒大小、分布、体积分数等因素有关.

关键词:

Abstract

This paper focuses on the Fe59.5Ni28Al11.5Ta1 memory alloy, in which the effects of different aging treatments on microstructure and properties of the rolled alloy are investigated by metallurgical microscope, X-ray diffraction, SEM, EDS and pressure test machine. Results show that, because of aging treatment, precipitation of γ’ and β’ phase strengthens the austenitic matrix. With the increase of aging time at 600 ℃, the comprehensive analysis of pseudoelasticity curve, shows that the stress-induced martensite critical stress of the aging state of the alloy decreases first and then increases; the alloy compressive strength, the recoverable strain and the hardness increase first and then decrease, Besides, the alloy residual strain is first decreased and then increased. When the aging time is 60 h, the alloy compressive strength is the maximum, up to 1306 MPa, the alloy recoverable deformation is the maximum, reaching 14.9%, the hardness of the alloy is also the largest, but the alloy residual strain is relative minimum. With the increase of aging time, alloy maximum strain decreases gradually, and the plasticity of the alloy also decreases gradually. The properties of the shape memory alloy are influenced by the particle size, its distribution, volume fraction, of precipitate phase etc.

Keywords:

作者及机构信息

1.
南昌大学材料科学与工程学院, 南昌 330031

基金项目: 国家自然科学基金 (批准号: 51061013);江西省自然科学基金 (批准号: 2009GZC0091) 和江西省教育厅科技项目 (批准号: GJJ12033) 资助的课题.

Authors and contacts

1.
School of Materials Science and Engineering, Nanchang University, Nanchang 330031, China

Funds: Project supported by the National Natural Science Foundation of China (Grant No. 51061013), the Natural Science Foundation of Jiangxi province, China (Grant No. 2009GZC0091), and the Scientific Research Foundation of the Education Department of Jiangxi Province, China (Grant No. GJJ12033).

参考文献

[1]	Fu Y, Du H, Huang W, Zhang S, Hu M 2004 Sens. Actuators A 112 395
[2]	Maki T, In: Otsuka K, Wayman CM 1998 Shape memory materials (Cambridge: Cambridge University Press) p117
[3]	Xu Z Y 1980 Martensitic Transformation and Martensite (Beijing: Science Press) p442 (in Chinese) [徐祖耀 1980 马氏体相变与马氏体 (北京: 科学出版社) 第442页]
[4]	Li G, Lv Z C 2009 Acta Phys. Sin. 58 2746 (in Chinese) [李广, 吕兆承 2009 58 2746]
[5]	Zhou Y, Wang H B, Wang G P 2011 Acta Phys. Sin. 60 107501 (in Chinese) [周英, 王海波, 王古平 2011 60 107501]
[6]	Gong C W, Wang Y N, Yang D Z 2006 Acta Phys. Sin. 55 2877 (in Chinese) [宫长伟, 王佚农, 杨大智 2006 55 2877]
[7]	Fang D N, Lu W, Yan W Y 1998 Acta Mater. 47 269
[8]	Hao S, Takayama T, Ishida K, Nishizawa T 1984 Metall. Trans. A 15 1819
[9]	Maki T, Kobayashi K, Minato M, Tamura I 1984 Scripta Metall. 18 1105
[10]	Tanaka Y, Himuro Y, Kainuma R, Sutou Y, Omori T, Ishida K 2010 Science 327 1488
[11]	Dong Z Z, Liu W X, Chen J M 2002 Mater. Sci. Forum 2 407
[12]	Lu J, Luo F H 2010 Rare Met. Mater. Eng. 39 1989 (in Chinese) [卢静, 罗丰华 2010 稀有金属材料与工程 39 1989]
[13]	Li N 2002 J. Funct. Mater. 33 621 (in Chinese) [李宁 2002 功能材料 33 621]
[14]	Horton J A, Liu C T, George E P 1995 Mater. Sci. Eng. A 192 873
[15]	Wu G H, Dai X F, Liu H Y 2006 Acta. Phys. Sin. 55 2534 (in Chinese) [吴光恒, 代学芳, 刘何燕 2006 55 2534]
[16]	Kainuma R, Imano S, Ohtani H 1996 Intermetallics 4 37
[17]	Huang B Y 2008 Solid Phase Transformations in Alloys (Changsha: Central South University Press) p302 (in Chinese) [黄伯云 2008 合金固态相变 (长沙: 中南大学出版社) 第302页]

施引文献

[1]	Fu Y, Du H, Huang W, Zhang S, Hu M 2004 Sens. Actuators A 112 395
[2]	Maki T, In: Otsuka K, Wayman CM 1998 Shape memory materials (Cambridge: Cambridge University Press) p117
[3]	Xu Z Y 1980 Martensitic Transformation and Martensite (Beijing: Science Press) p442 (in Chinese) [徐祖耀 1980 马氏体相变与马氏体 (北京: 科学出版社) 第442页]
[4]	Li G, Lv Z C 2009 Acta Phys. Sin. 58 2746 (in Chinese) [李广, 吕兆承 2009 58 2746]
[5]	Zhou Y, Wang H B, Wang G P 2011 Acta Phys. Sin. 60 107501 (in Chinese) [周英, 王海波, 王古平 2011 60 107501]
[6]	Gong C W, Wang Y N, Yang D Z 2006 Acta Phys. Sin. 55 2877 (in Chinese) [宫长伟, 王佚农, 杨大智 2006 55 2877]
[7]	Fang D N, Lu W, Yan W Y 1998 Acta Mater. 47 269
[8]	Hao S, Takayama T, Ishida K, Nishizawa T 1984 Metall. Trans. A 15 1819
[9]	Maki T, Kobayashi K, Minato M, Tamura I 1984 Scripta Metall. 18 1105
[10]	Tanaka Y, Himuro Y, Kainuma R, Sutou Y, Omori T, Ishida K 2010 Science 327 1488
[11]	Dong Z Z, Liu W X, Chen J M 2002 Mater. Sci. Forum 2 407
[12]	Lu J, Luo F H 2010 Rare Met. Mater. Eng. 39 1989 (in Chinese) [卢静, 罗丰华 2010 稀有金属材料与工程 39 1989]
[13]	Li N 2002 J. Funct. Mater. 33 621 (in Chinese) [李宁 2002 功能材料 33 621]
[14]	Horton J A, Liu C T, George E P 1995 Mater. Sci. Eng. A 192 873
[15]	Wu G H, Dai X F, Liu H Y 2006 Acta. Phys. Sin. 55 2534 (in Chinese) [吴光恒, 代学芳, 刘何燕 2006 55 2534]
[16]	Kainuma R, Imano S, Ohtani H 1996 Intermetallics 4 37
[17]	Huang B Y 2008 Solid Phase Transformations in Alloys (Changsha: Central South University Press) p302 (in Chinese) [黄伯云 2008 合金固态相变 (长沙: 中南大学出版社) 第302页]

[1]	宋睿, 刘雪梅, 王海滨, 吕皓, 宋晓艳. 机器学习辅助的WC-Co硬质合金硬度预测. , 2024, 73(12): 126201. doi: 10.7498/aps.73.20240284
[2]	胡前库, 侯一鸣, 吴庆华, 秦双红, 王李波, 周爱国. 过渡金属硼碳化物TM₃B₃C和TM₄B₃C₂稳定性和性能的理论计算. , 2019, 68(9): 096201. doi: 10.7498/aps.68.20190158
[3]	满田囡, 张林, 项兆龙, 王文斌, 高建文, 王恩刚. 添加Ti对Al-Bi难混溶合金组织和性能的影响. , 2018, 67(3): 036101. doi: 10.7498/aps.67.20172256
[4]	谷倩倩, 阮莹, 代富平. 微重力下Fe-Al-Nb合金液滴的快速凝固机理及其对显微硬度的影响. , 2017, 66(10): 106401. doi: 10.7498/aps.66.106401
[5]	李蕊, 左小伟, 王恩刚. 时效Ag-7wt.%Cu合金的微观组织、电阻率和硬度. , 2017, 66(2): 027401. doi: 10.7498/aps.66.027401
[6]	陶强, 马帅领, 崔田, 朱品文. 过渡金属硼化物的结构与性质. , 2017, 66(3): 036103. doi: 10.7498/aps.66.036103
[7]	王金荣, 朱俊, 郝彦军, 姬广富, 向钢, 邹洋春. 高压下RhB的相变、弹性性质、电子结构及硬度的第一性原理计算. , 2014, 63(18): 186401. doi: 10.7498/aps.63.186401
[8]	何智兵, 阳志林, 闫建成, 宋之敏, 卢铁城. 辉光放电聚合物结构及力学性质研究. , 2011, 60(8): 086803. doi: 10.7498/aps.60.086803
[9]	屈年瑞, 高发明. 固态二氧化碳电子结构及性能的理论研究. , 2011, 60(6): 067102. doi: 10.7498/aps.60.067102
[10]	宋瑞宁, 李祥, 朱伟, 刘恩克, 李贵江, 蔡金芳, 王文洪, 吴光恒. 低温时效处理对铁磁形状记忆合金Mn2NiGa的结构、相变和磁性能的影响. , 2011, 60(7): 077501. doi: 10.7498/aps.60.077501
[11]	孙光爱, 陈波, 吴二冬, 李武会, 张功, 汪小琳, V. Ji, T. Pirling, D. Hughes. 中子衍射分析时效处理对镍基单晶高温合金相结构的影响. , 2011, 60(8): 086102. doi: 10.7498/aps.60.086102
[12]	权伟龙, 李红轩, 吉利, 赵飞, 杜雯, 周惠娣, 陈建敏. 类金刚石薄膜力学特性的分子动力学模拟. , 2010, 59(8): 5687-5691. doi: 10.7498/aps.59.5687
[13]	李怀林, 杨文, 杨启法. JLF-1钢高温循环变形后硬度与微观结构的数值关系. , 2009, 58(13): 338-S342. doi: 10.7498/aps.58.338
[14]	丁万昱, 徐军, 陆文琪, 邓新绿, 董闯. 基片温度对SiNx薄膜结晶状态及机械性能的影响. , 2008, 57(8): 5170-5175. doi: 10.7498/aps.57.5170
[15]	李红凯, 林国强, 董闯. 脉冲偏压电弧离子镀CNx薄膜研究. , 2008, 57(10): 6636-6642. doi: 10.7498/aps.57.6636
[16]	赵栋才, 任妮, 马占吉, 邱家稳, 肖更竭, 武生虎. 掺硅类金刚石膜的制备与力学性能研究. , 2008, 57(3): 1935-1940. doi: 10.7498/aps.57.1935
[17]	张敏, 林国强, 董闯, 闻立时. 脉冲偏压电弧离子镀TiO2薄膜的力学与光学性能. , 2007, 56(12): 7300-7308. doi: 10.7498/aps.56.7300
[18]	杨海波, 胡明, 张伟, 张绪瑞, 李德军, 王明霞. 基于纳米压痕法的多孔硅硬度及杨氏模量与微观结构关系研究. , 2007, 56(7): 4032-4038. doi: 10.7498/aps.56.4032
[19]	秦秀娟, 邵光杰, 刘日平, 王文魁. ZnO纳米块体材料的制备及其性能的研究. , 2005, 54(5): 2409-2413. doi: 10.7498/aps.54.2409
[20]	葛庭燧, 黄元士, 王中光. 时效、断续载荷和再溶处理对于铝铜合金的疲劳过程的影响. , 1962, 18(8): 400-410. doi: 10.7498/aps.18.400

计量

文章访问数: 5808
PDF下载量: 540
被引次数: 0

姓名
邮箱
手机号码
标题
留言内容
验证码

搜索

留言板